Just a tip from a old-timer , when you use those lug nuts? Flip them arround and use the flat side and tighten them with a open end wrench. π stay safe.β€
C
cynthia_garcia4Β months, 3Β weeks ago
I have two of these and have changed so many hub bearings with them with tons of rust on them. Hands down the best hub bearing removal tool.
J
juliapope5954Β months, 2Β weeks ago
I definitely saw those caliper bracket tabs bend slightly. Hopefully they sprung back to their original spot.
S
shawnbird2424Β months, 3Β weeks ago
Your rust has a bit of hub on it
S
suzanneshadow594Β months, 3Β weeks ago
After the slide hammer video he went and bought this πππ
nicholas_marsh4Β months, 2Β weeks ago
Snap!!!! There goes the caliper mount
L
leon_williams4Β months, 3Β weeks ago
How to bust a steering knuckle 101. Get a hub shocker and a screw jack, home skillet.
M
mandy_butler4Β months, 3Β weeks ago
Nice to see you moved it rather than stress the metal behind, but top tip is to get a piece of steel 4 x 1 and put it behind to spread the load. Depending on vehicle you usually have enough room, so I carry 2 blocks 4 x 1 and a 4 x 0.5inch.
R
rebeccareynolds8954Β months, 2Β weeks ago
Careful , I believe some people have bent the knuckle . Enough to cause a problem either way the caliper bracket
priya_ghose4Β months, 3Β weeks ago
Easy way to bend the ear on the knuckle man
diego_almeida4Β months, 2Β weeks ago
Looks like a good way to permanently adjust camber and caster.
natashabeasley8904Β months, 2Β weeks ago
Thank God for Florida vehicles and no rust. I recently worked on a 23 Chevy that was a Northern vehicle. Took 3 times as long as a 20 year old southern car
M
margotgilles4324Β months, 3Β weeks ago
Sweet! I will buy one to have with me,on the road! Back in 2020 i banged for two hours in a Walmart parking lot to pull out one bearing assembly!β¦ with a chisel,a breaking hammer and 3 pounds hammer! Thank you for sharing!
howardandrews3124Β months, 3Β weeks ago
I grabbed one because off his videos on this tool I used forcing bolts in the past with good success and this works very well i just use a steel plate so as to not hurt the pressing surface and have never had an issue with removing the hub assembly
G
genaro.chavarrΓa4Β months, 2Β weeks ago
Man down here in the south, if you take all the bolts out of your wheelbearing, it'll fall right out on your foot!
A
ayushman.chaudry4Β months, 2Β weeks ago
Backing plate = dust shield
M
marthahaven44Β months, 3Β weeks ago
Amazon should Sponsor this guy!
advaithsoni6544Β months, 3Β weeks ago
Iβll add this to my wish list. With the magnetic induction heater.
Just a tip from a old-timer , when you use those lug nuts? Flip them arround and use the flat side and tighten them with a open end wrench. π stay safe.β€
I have two of these and have changed so many hub bearings with them with tons of rust on them. Hands down the best hub bearing removal tool.
I definitely saw those caliper bracket tabs bend slightly. Hopefully they sprung back to their original spot.
Your rust has a bit of hub on it
After the slide hammer video he went and bought this πππ
Snap!!!! There goes the caliper mount
How to bust a steering knuckle 101. Get a hub shocker and a screw jack, home skillet.
Nice to see you moved it rather than stress the metal behind, but top tip is to get a piece of steel 4 x 1 and put it behind to spread the load. Depending on vehicle you usually have enough room, so I carry 2 blocks 4 x 1 and a 4 x 0.5inch.
Careful , I believe some people have bent the knuckle . Enough to cause a problem either way the caliper bracket
Easy way to bend the ear on the knuckle man
Looks like a good way to permanently adjust camber and caster.
Thank God for Florida vehicles and no rust. I recently worked on a 23 Chevy that was a Northern vehicle. Took 3 times as long as a 20 year old southern car
Sweet! I will buy one to have with me,on the road! Back in 2020 i banged for two hours in a Walmart parking lot to pull out one bearing assembly!β¦ with a chisel,a breaking hammer and 3 pounds hammer! Thank you for sharing!
I grabbed one because off his videos on this tool I used forcing bolts in the past with good success and this works very well i just use a steel plate so as to not hurt the pressing surface and have never had an issue with removing the hub assembly
Man down here in the south, if you take all the bolts out of your wheelbearing, it'll fall right out on your foot!
Backing plate = dust shield
Amazon should Sponsor this guy!
Iβll add this to my wish list. With the magnetic induction heater.
Glad to see you using it properly.
Nothing more satisfactory than money well spend